High-Pass Filter
SHPF-6585-FAll-in-one brass structure with nickel-plated surfa Small size fit for indoor use. Can be installed separately, or as…

The S0T-03-1G-C-**dBm downstream optical transmitter supports 870/1003/1218Mhz band and the DOCSIS 3.1 standard. The output optical power is from +6 dBm to +15 dBm available. It can be used for optical fiber transmission of downstream analog TV signals, digital television signals and CMTS data signals in HFC network. It has patented pre-distortion circuit, high CNR and low distortion.
The specifications below are taken from the product catalog.
Schematic diagram

Specifications
| Characteristics | Unit | Value/Performance |
| Optical Parameters | ||
| Laser Type | - | DFB Laser Module (OC-48 pinout compatible), with Isolator, with CNR = 51 dB min., CSO = 60 dB min., CTB = 65 dB min., with brand name from G7/EU countries |
| Center Wavelength | nm | 1310 ± 10 |
| Connector | - | SC/APC (sleeve material: ceramic, connector with shutter) |
| Output Power | mW | ≥ 6.3 (8dBm) or ≥ 20 (13dBm) |
| RF Parameters | ||
| Input Level | dBmV/ch | 15 to 25, or larger |
| RF Amplifier Technology | - | 1 * CATV GaAs or GaN Push-Pull and 1 * CATV GaAs or GaN Power-Doubler Hybrid Amp. Modules. All have brand name from G7/EU countries |
| Gain Control Range | dB | 0 ~ 10, or larger |
| Input Impedance | Ω | 75 |
| Return Loss | dB | ≥ 16 dB |
| Bandwidth | MHz | 82 to 1000, or larger |
| Flatness | dB | ≤ ± 0.75 |
| Channel Loading | - | 77 NTSC / 60 PAL channels + 320 MHz digital channels |
| Link Performance | ||
| (Test at temperature 25 degree C, 77 NTSC channels / 60 PAL channels Loading) | - | |
| CNR | dB | ≥ 52 @ link loss = 14dB ; ≥ 51 @ link loss = 15 dB |
| CSO | dB | ≤ -63 |
| CTB | dB | ≤ -65 |
| Others | ||
| Control Interface | - | RS232 / RS485 and RJ45. Support MIB table for SNMP Monitoring software |
| Power Supply | V | 100 to 240 VAC, 50/60 Hz, or larger |
| Operating Temperature | °C | 0 to 50, or larger |
Structure Description

Front panel
| 1 | Power indicator |
| 2 | Laser drive level indicator: Steady green light: Drive level is normal. Blinking red light: Drive level alarm. You can view the alarm in the Alarm Status, the second level submenu. |
| 3 | Laser working status indicator: Steady green light: The laser is operating normally. Steady red light: The laser is not turned on. Blinking red light: The device has a parameter alarm. You can view the alarm in the Alarm Status, the second level submenu. |
| 4 | Device running indicator: This indicator will flash by 1Hz frequency after the device start running normally. |
| 5 | Laser switch: ON: The laser is on. OFF: The laser is off. Keep the laser off before the device is powered on, and turn on the laser after the self-inspection is completed when power on. |
| 6 | Laser drive level test port: -20dB |

Rear panel
| 1 | Fan | 6 | RS232 interface |
| 2 | Ground stud, ensure good grounding before power on | 7 | LAN interface |
| 3 | RF input 1 | 8 | Power module 1, hot swappable |
| 4 | RF input 1 test port -20dB | 9 | Power module 2, hot swappable |
| 5 | Optical signal output |
Dimension

Send a request to get help choosing equipment and a connection plan.